KDS FLYMENTOR DRIVERS FOR MAC

May 4, 2018 Literature

You’ll receive email and Feed alerts when new items arrive. Please do not purchase this item if you do not agree. This gyro also contain some Temperature sensor and some other sensors too. Because the blue wire is disconnected, The FM gain it controlled by Helibal. The sensor of Flymentor 3D must be mounted horizontally.

Uploader: Bralar
Date Added: 10 October 2012
File Size: 34.1 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 93279
Price: Free* [*Free Regsitration Required]

If the elevator kds flymentor is front mounted, The left servo to port 2 and right servo to port 1. Guaranteed Delivery see all Guaranteed Delivery. You will not get all servo at exactly at 90 degrees just get them as close as possible. During adjusting, please be careful about following: Number of bids and bid foymentor may be slightly out of date. kds flymentor

Helipal.com – DJI Products Special Arrangement

CCD sensor to capture picture of kds flymentor, comparing pictures to avoid drifting. Customers who bought this product also purchased.

Please enable JavaScript on your browserthen try again. Are you saying it corrects kds flymentor on kds flymentor but not on elevator Are the servos moving at all when you tip the hel forwards. Originally Posted by Fayez NoteIf the blue wire is connected stabilization gain is controlled kds flymentor adjusted in the TX and adjusting it in Helibal will have no effect, if it is disconnected stabilization gain is adjusted in Helibal. Looking at the heli from the side use the elevator neutral slider under the servo tab to level the swash, looking at the helicopter from the front use aileron slider to level the swash.

If you are using kds flymentor separate tail gyro leave it connected as it is to the Rx, and leave the gray and green wires disconnected.

FlyMentor Setup By Ivor Hill PLEASE READ FIRST!! – HeliFreak

Originally Posted by fastboyy. Originally Posted by helican. Connected,controlled by TX disconnected controlled in Helibal.

If it found that the images is not same as the previous image, it will adjust the servo and auto correct it for you! HTML is not translated! My best guess is that because the kds flymentor is fitted upside down it is working in the opposite direction so I guess the kds flymentor will be to turn the camera around.

Switch to Threaded Mode. In order to be able to post messages on the HeliFreak forums, you ,ds first register.

KDS Flymentor 3D Auto Pilot Stabilizer System

If you can get aileron to operate, but not elevator the swap servo connections on FM ports 1 flymenor 2 and start again. Switch working mode horizontal mode and position mode through AUX channel.

The CCD Camera’s job is to take image of kds flymentor ground, then to provide a signal to the Flymentor Mixer, and gives the correction to the cyclic servos.

Disconnect motor, power up TX and Helicopter, LED on FM kds flymentor be flashing green, and connect to Helibal Program Check that swash type,blade direction and gyro camera directions are set correctly under the Helibal mounting tab. The wire should twist magnetic ring for three circles at least. When wind pass thru the helicopter, it will push the kds flymentor and making it up side down, you will need to adjust the control sticks constantly to prevent this from happening.

Flymentor 3D helicopter stabilisation System

If the elevator servo is rear mounted, looking at the helicopter from the kds flymentor. Buy It Now 3. Once in normal mode the tail servo will move to center, set the tail slider so that it is a little off center this is to counter the rotor torque Test kds flymentor and slide the servo along the boom until the helicopter will kfs without stick input or trim.

Leave the blue wire from the FM gyro disconnected for now.

Originally Posted by Ivor Hill My best guess is that because the gyro is fitted upside down it is working in the opposite direction so I guess the fix kds flymentor be to turn the camera around.

Under this mode, there will rlymentor solid red and green light on the Flymentor Mixer, the CCD will not be working, only the 3-Axis Gyro is kds flymentor. Balance mode is working correctly, rudder is OK. If kds flymentor are newbie, please do not purchase it, it is not for you. Have you kdw it?.